Introduction: Detailing workstation retrofits often combine water, air, and electrical service at the same bay, and the practical starting point is the modular reel series already available. A buildable configuration comes from selecting the drum mix, confirming label authorization, and sending the station details needed for a quotation.
Projects that call for custom hose reels for automotive detailing workstations can often be met by combining existing modular water, air, and electrical drums. A retrofit generally needs water for rinsing and bucket fill, air for blow-off and drying, and power for a polisher or work lamp. The practical task is to define how those functions share a bank, which end covers close the run, which plug type the electrical drum needs, and what label artwork will be applied. The answer should be a buildable configuration within the current series, not a new housing program.
Supported Modular Configurations for Multi-Drum Hose Reel Projects
The series uses one shared frame interface. Water, air, and electrical drums share the same side-connection pattern and housing footprint, so a station can start with a single water reel and later grow into a three-drum bank. In a detailing bay, that usually means a water drum for rinse and bucket filling, an air drum for blow-off and drying, and an electrical drum for a polisher or work lamp. Because the drums share the same body size, color, and mounting logic, the bank reads as one piece of shop equipment. The water drum sets the plumbing side. SGGF232 is a 1.2 MPa normal-pressure reel with a 10 m hose split into a 1 m inlet section, an 8 m wound length, and a 1 m outlet section. It uses an 8 x 12 mm three-layer polyether TPU hose, a 16 mm brass quick outlet, and a 1/2 in. male inlet thread. That covers rinse water, pre-soak, bucket fill, and wheel work at the station. A high-pressure washer runs on its own dedicated line and does not route through this reel, which keeps the pressure duty where it belongs.
1. Interlocking Banks Let Water, Air, and Electrical Reels Share One Frame
The interlocking side connection makes a multi-drum modular hose reel bank practical on a retrofit. Once the first drum is in place, the next one clips onto its flank, so the run grows sideways without a new bracket and anchor point for every function. Reel heights line up automatically, service access stays on one face, and identical bays can be repeated from one bay definition. For example, water plus air can serve every wash bay, with an electrical drum added only where polishing or inspection lighting is part of the process. A two-drum and a three-drum station are the same configuration problem, just one drum longer.
2. End Covers and Plug Standards Define Practical Series Fit
End covers close the exposed ends of an assembled bank. They tidy the silhouette, protect the interlock edges and drum internals at the outer positions, and give the station a finished appearance. Plug choice belongs to the electrical drum only and should be settled for the destination market. The series offers Type B, Type F, Type G, and Type I plug configurations, with two-core and three-core versions, so the same bank design can ship to North America, Europe, the UK, or Asia without changing the housing. Standardized socket families differ by region, which is why plug type is a project input.
OEM/ODM Brand Labels and Trademark Permissions
Integrators and distributors often want their own mark on the bank: a house brand on the housing, an end-cover logo, or a label for a specific chain account. The first point to settle is who owns the mark. A trademark identifies the source of goods, and registration gives the owner the right to use it and to authorize others to use it. Written permission should therefore sit at the center of any OEM/ODM labeling request. In practice, the distributor sends the brand name and logo artwork, states whether they own the mark or are acting for the owner, and confirms in writing that the label may be applied to the agreed quantity of reels. If the label belongs to a third party—a chain customer, a parent company, or an importer's own brand—the permission comes from that owner, not from whoever placed the order. Once authorization is on file, label scope can cover logo placement on the housing or end covers, artwork on the carton, and matching artwork across the drums in a bank. The structure underneath stays the standard modular body; branding is applied to the existing series rather than driving a new housing design.
How to Prepare a Clear Custom Hose Reel Inquiry for a Detailing Workstation Project
A useful inquiry describes the bank, not just the product category. Start with the number of stations and, for each one, the drum mix in the order it should sit in the run. Then add the details that change a build: whether the water outlet needs to reach further than the standard 1 m hanging section, since the outlet side supports up to 5 m of extension for a 15 m working reach; which plug configuration each electrical drum needs for its destination market; whether a bank is closed with end covers at both ends or continues as a longer run; and whether any location carries a brand label. Finish with the destination market and whether the units ship as individual cartons or a consolidated project shipment. A described bank produces a quotation for the specified combination. When you work with a hose reel supplier on a retractable hose reel wholesale order for a multi-site rollout, that discipline pays twice: the same combination repeats across every bay, and the second site is a copy of the first rather than a new engineering exercise. Pricing and delivery terms come back with the quotation for the combination you send.
Conclusion
Most detailing workstation retrofits can be built from the modular series as it stands: one frame shared by water, air, and electrical drums, interlocking side connections to grow a bank, end covers to finish it, and plug options that let the electrical drum match the local market. The configuration work is choosing the mix, the order, the outlet reach, and the label—not redesigning the reel. New molds, structural redesign, new pressure ratings, electrical features on the water reel, certification, MOQ, price, and lead time require separate confirmation. SGCB supplies the SGGF232 water drum and the matching series drums from existing molds. Send the station count, drum mix, plug type, end-cover layout, extension length, and brand-label authorization, and the combination can be confirmed as a buildable project.
FAQ
Q: Can the SGGF232 water hose reel be customized with a different internal structure?
A: The water drum is built on existing tooling, so the rewind mechanism, drum core, 8 x 12 mm TPU hose, and 1.2 MPa normal-pressure rating stay as they are. A different internal structure would be a new mold program and sits outside the modular option set. Project-specific choices cover how many units share a bank, end covers, outlet extension up to 5 m, and label artwork.
Q: Which parts of a modular hose reel project can be configured?
A: You can configure the number of drums per bank, the mix of water, air, and electrical units, their order in the run, end covers, outlet extension length on the water side, the plug type and core count on the electrical drum, and brand labeling. The housing, the hose specification, the 16 mm brass quick outlet, and the pressure rating of the water drum are fixed on the SGGF232 water reel.
Q: Do OEM/ODM projects require written permission to use a distributor brand?
A: Yes. When the label belongs to the distributor or to their own customer, written authorization allows the mark to be applied to the reels. Send the brand name and logo artwork together with a short written statement that the requester owns the mark or is authorized by the owner. If the mark belongs to a third party, that owner provides the permission.